Heat Shields

Safe distances matter – heat and combustibles don’t mix.

Heat shield fitted to protect the beam – job done.
Shame the customer parked the logs & log basket a bit too close to the stove afterwards!

Stoves and flues generate intense heat, and anything combustible nearby is a risk. Building Regulations – and each stove manufacturer – set minimum clearance rules to keep your home safe and your installation compliant. This guide explains what counts as combustible, the distances required, and the heat shield solutions that make real-world installations practical.

Combustible Materials

Combustible materials include wood, plastic, plasterboard, electrical wires and sockets, wallpaper, and curtains.

If these fall within the clearance zone of either the stove or the flue, the safest option is to remove them completely.

Why It Matters

Building Regulations and stove manufacturers set strict rules on how close appliances and flues can be to combustibles. This is to prevent heat build-up, fire risk, and failed certification. Manufacturer’s instructions always override general guidelines.

Flues – Safe Distances

  • Building Regulations set minimum clearances between flue pipes and combustible materials.

  • These rules vary depending on whether the pipe is single wall (vitreous enamel) or insulated twin wall.

 

Single Wall Flue (vitreous enamel stove pipe):

  • 125mm / 5″ pipe – minimum 375mm / 15″ clearance to combustibles.

  • 150mm / 6″ pipe – minimum 450mm / 18″ clearance to combustibles.

  • In most homes, these clearances are impractical – the pipe would sit too far from the wall.

 

Twin Wall Flue (insulated system):

  • Approx. 200mm / 8″ external diameter with insulation between inner and outer casings.

  • Can be installed as close as 50mm / 5cm to plasterboard, wood, or other combustible surfaces.

  • This makes twin wall the realistic choice where space is tight or when passing through ceilings, lofts, and external walls.

 

Non-Combustible Walls

  • As with stoves, if the flue passes close to solid dense blockwork, brickwork, or stone, these are classed as non-combustible.

  • Standard clearance rules don’t apply against these surfaces.

Stoves – Safe Distances

  • Most stoves need 500–600mm clearance to combustibles at the back, sides, and top.

  • Every manufacturer will specify their own distance-to-combustibles, and those figures always take priority.

  • Many models have built-in shields or optional clip-on panels that reduce these clearances.

 

Cylindrical stoves (e.g. Scandinavian designs like Contura):

  • Metal shroud casing makes them well-suited to freestanding corner installs.

  • Some models allow as little as 100mm clearance to plasterboard walls. Others are 50mm or 150mm – all workable figures.

  • More than that pushes the stove too far into the room. It looks wrong and usually makes the install impractical.

 

Rectangular or square stoves:

  • Optional rear and side shields typically reduce distances to 100–300mm, depending on the model.

 

Non-Combustible Walls

  • Solid dense blockwork (100mm thick or more) is classed as non-combustible.

  • Brickwork and stone walls are also non-combustible.

  • Where these are in place, clearance requirements to the wall don’t apply – they’re always sufficient.

Wall-Mounted Heat Shields

If stove shields aren’t available – or if you prefer to use a single wall flue for extra heat output – a wall-mounted heat shield may be required.

A compliant wall-mounted shield must:

  • Be spaced 25mm / 2.5cm off the wall to create an air gap

  • Overlap the stove and flue by at least 150mm / 15cm each side

  • Extend at least 300mm / 30cm above the stove and pipe

This setup can reduce clearances to around 100mm, subject to the stove manufacturer’s guidance.

Heat Shield Options

  • 12mm Cement Board – affordable, basic, can be rendered, tiled, or painted (though prone to flaking if untreated).

  • Fireboard – similar to cement board but designed specifically for fire resistance; more expensive.

  • 1.6mm Galvanised Steel – robust with an industrial look; scratches easily if painted.

  • Vlaze Heat Shields – premium finish, stylish and durable, but higher cost.

Not sure what applies in your home?

That’s why we’re here. Clearances depend on your stove, flue, and the walls around it. Send us a few photos and we’ll check the specs for you – then provide a clear, all-in estimate for the right solution.